Hi,
Short version:
Is BS 10001 output working on linux with a SBS-3 connected up via USB?
Long version:
I have a Kinetics SBS-3 running firmware V119.
I am running the SBS-3 via a USB connection on the Raspberry PI with build 1.0.16-7. I want to have the raspberry PI running the SBS-3 as I can put it in the roof on a short antenna run. I can then run basestation when a PC is on if so desired. The 10001 feed does not appear to be working. I also can't see output on the RAW feed (although the port is open).
I have the following config:
MPX is the switch for the 10001 output, BS for 30003 and RAW 30334. BS output works fine. I am unsure if RAW is working but you can see it open the port in the log. 10001 is not opened.
Things also look fine on the feeder status page:
Netstat:
Any thoughts or suggestions on how I can get the BS 10001 feed and the 30034 RAW feed going properly?
Thanks
Chris
Short version:
Is BS 10001 output working on linux with a SBS-3 connected up via USB?
Long version:
I have a Kinetics SBS-3 running firmware V119.
I am running the SBS-3 via a USB connection on the Raspberry PI with build 1.0.16-7. I want to have the raspberry PI running the SBS-3 as I can put it in the roof on a short antenna run. I can then run basestation when a PC is on if so desired. The 10001 feed does not appear to be working. I also can't see output on the RAW feed (although the port is open).
I have the following config:
receiver="sbs3usb"
fr24key="XXXXXXXXX"
host="localhost"
path="/dev/ttyUSB1"
baudrate="921600"
bs="no"
raw="yes"
mpx="yes"
baudrate="921600"
logmode="2"
windowmode="0"
mpx="yes"
mlat="yes"
mlat-without-gps="yes"
fr24key="XXXXXXXXX"
host="localhost"
path="/dev/ttyUSB1"
baudrate="921600"
bs="no"
raw="yes"
mpx="yes"
baudrate="921600"
logmode="2"
windowmode="0"
mpx="yes"
mlat="yes"
mlat-without-gps="yes"
MPX is the switch for the 10001 output, BS for 30003 and RAW 30334. BS output works fine. I am unsure if RAW is working but you can see it open the port in the log. 10001 is not opened.
2015-12-27 13:14:48 | [main][i]FR24 Feeder/Decoder [0x02117000]
2015-12-27 13:14:48 | [main][i]Version: 1.0.16-7/generic
2015-12-27 13:14:48 | [main][i]Built on 20151214-1410 (r:master-d6572f3.git/Linux/armv7l)
2015-12-27 13:14:48 | [main][i]Copyright 2012-2015 Flightradar24 AB
2015-12-27 13:14:48 | [main][i]hxxp://flightradar24.com)
2015-12-27 13:14:48 | [main][i]DNS mode: LIBC
2015-12-27 13:14:48 | [main][i]Automatic updates are ENABLED
2015-12-27 13:14:48 | [main][i]Reader 0 started
2015-12-27 13:14:48 | [main][i]MLAT data feed started
2015-12-27 13:14:48 | [reader][i][0]Initializing reader
2015-12-27 13:14:48 | [httpd][i]Server started, listening on 0.0.0.0:8754
2015-12-27 13:14:48 | [master][i]Starting processing thread
2015-12-27 13:14:48 | [reader][i][0]Connecting to SBS3 receiver via USB (/dev/ttyUSB1)
2015-12-27 13:14:48 | [mlat][i]Waiting for MLAT configuration
2015-12-27 13:14:48 | [reader][i][0]Connected to the receiver, authenticating
2015-12-27 13:14:49 | [reader][i][0]Authenticated, processing messages
2015-12-27 13:14:49 | [time][i]Synchronizing time via NTP
2015-12-27 13:14:57 | [time][i]Time synchronized correctly, offset -0.0003 seconds
2015-12-27 13:14:57 | [main][i]Feed Network client started
2015-12-27 13:14:57 | [main][i]RAW data server started
2015-12-27 13:14:57 | [raw][i]Initializing server
2015-12-27 13:14:57 | [raw][i]Starting server on 0.0.0.0:30334
2015-12-27 13:14:57 | [feed][i]Downloading configuration
2015-12-27 13:14:58 | [feed][c]Interval: 5s
2015-12-27 13:14:58 | [feed][c]Latitude: -XX.XXXX
2015-12-27 13:14:58 | [feed][c]Longitude: 1XX.XXXX
2015-12-27 13:14:58 | [feed][c]GND: YES
2015-12-27 13:14:58 | [feed][c]NonADSB: YES
2015-12-27 13:14:58 | [feed][c]Timestamps: optional
2015-12-27 13:14:58 | [feed][c]Max range AIR: 350.0nm
2015-12-27 13:14:58 | [feed][c]Max range GND: 100.0nm
2015-12-27 13:14:58 | [feed][i]defined 2 servers
2015-12-27 13:14:58 | [feed][n]YMXXX@aus-1.fr24.com:8099/TCP
2015-12-27 13:14:58 | [feed][n]connecting
2015-12-27 13:14:58 | [stats][i]Stats thread started
2015-12-27 13:14:58 | [mlat][i]MLAT configuration received, service ENABLED
2015-12-27 13:14:58 | [mlat][i]Starting MLAT with preconfigured position: -XX.XX,XXX.XX,XXX.0
2015-12-27 13:14:58 | [mlat][i]MLAT bandwidth reduction active, level 1
2015-12-27 13:14:58 | [mlat][i]Configuring UDP connection udp:54.XX.XXX.XXX:19788
2015-12-27 13:14:58 | [mlat][i]Registering MLAT station
2015-12-27 13:14:58 | [mlat][i]Registering MLAT station: SUCCESS
2015-12-27 13:14:48 | [main][i]Version: 1.0.16-7/generic
2015-12-27 13:14:48 | [main][i]Built on 20151214-1410 (r:master-d6572f3.git/Linux/armv7l)
2015-12-27 13:14:48 | [main][i]Copyright 2012-2015 Flightradar24 AB
2015-12-27 13:14:48 | [main][i]hxxp://flightradar24.com)
2015-12-27 13:14:48 | [main][i]DNS mode: LIBC
2015-12-27 13:14:48 | [main][i]Automatic updates are ENABLED
2015-12-27 13:14:48 | [main][i]Reader 0 started
2015-12-27 13:14:48 | [main][i]MLAT data feed started
2015-12-27 13:14:48 | [reader][i][0]Initializing reader
2015-12-27 13:14:48 | [httpd][i]Server started, listening on 0.0.0.0:8754
2015-12-27 13:14:48 | [master][i]Starting processing thread
2015-12-27 13:14:48 | [reader][i][0]Connecting to SBS3 receiver via USB (/dev/ttyUSB1)
2015-12-27 13:14:48 | [mlat][i]Waiting for MLAT configuration
2015-12-27 13:14:48 | [reader][i][0]Connected to the receiver, authenticating
2015-12-27 13:14:49 | [reader][i][0]Authenticated, processing messages
2015-12-27 13:14:49 | [time][i]Synchronizing time via NTP
2015-12-27 13:14:57 | [time][i]Time synchronized correctly, offset -0.0003 seconds
2015-12-27 13:14:57 | [main][i]Feed Network client started
2015-12-27 13:14:57 | [main][i]RAW data server started
2015-12-27 13:14:57 | [raw][i]Initializing server
2015-12-27 13:14:57 | [raw][i]Starting server on 0.0.0.0:30334
2015-12-27 13:14:57 | [feed][i]Downloading configuration
2015-12-27 13:14:58 | [feed][c]Interval: 5s
2015-12-27 13:14:58 | [feed][c]Latitude: -XX.XXXX
2015-12-27 13:14:58 | [feed][c]Longitude: 1XX.XXXX
2015-12-27 13:14:58 | [feed][c]GND: YES
2015-12-27 13:14:58 | [feed][c]NonADSB: YES
2015-12-27 13:14:58 | [feed][c]Timestamps: optional
2015-12-27 13:14:58 | [feed][c]Max range AIR: 350.0nm
2015-12-27 13:14:58 | [feed][c]Max range GND: 100.0nm
2015-12-27 13:14:58 | [feed][i]defined 2 servers
2015-12-27 13:14:58 | [feed][n]YMXXX@aus-1.fr24.com:8099/TCP
2015-12-27 13:14:58 | [feed][n]connecting
2015-12-27 13:14:58 | [stats][i]Stats thread started
2015-12-27 13:14:58 | [mlat][i]MLAT configuration received, service ENABLED
2015-12-27 13:14:58 | [mlat][i]Starting MLAT with preconfigured position: -XX.XX,XXX.XX,XXX.0
2015-12-27 13:14:58 | [mlat][i]MLAT bandwidth reduction active, level 1
2015-12-27 13:14:58 | [mlat][i]Configuring UDP connection udp:54.XX.XXX.XXX:19788
2015-12-27 13:14:58 | [mlat][i]Registering MLAT station
2015-12-27 13:14:58 | [mlat][i]Registering MLAT station: SUCCESS
Things also look fine on the feeder status page:
ac_map_size="3072"
build_arch="armv7l"
build_flavour="generic"
build_os="Linux"
build_revision="master-d6572f3.git"
build_timetamp="20151214-1410"
build_version="1.0.16-7"
cfg_baudrate="921600"
cfg_bs="no"
cfg_host="localhost"
cfg_mpx="yes"
cfg_path="/dev/ttyUSB1"
cfg_raw="yes"
cfg_receiver="sbs3usb"
cfg_windowmode="0"
build_arch="armv7l"
build_flavour="generic"
build_os="Linux"
build_revision="master-d6572f3.git"
build_timetamp="20151214-1410"
build_version="1.0.16-7"
cfg_baudrate="921600"
cfg_bs="no"
cfg_host="localhost"
cfg_mpx="yes"
cfg_path="/dev/ttyUSB1"
cfg_raw="yes"
cfg_receiver="sbs3usb"
cfg_windowmode="0"
Netstat:
tcp 0 0 *:30334 *:* LISTEN
tcp 0 0 *:8754 *:* LISTEN
tcp 0 0 *:ssh *:* LISTEN
tcp 0 0 *:8754 *:* LISTEN
tcp 0 0 *:ssh *:* LISTEN
Any thoughts or suggestions on how I can get the BS 10001 feed and the 30034 RAW feed going properly?
Thanks
Chris